precision raises a handful of sensible questions. This page answers them in order, starting with the fundamentals and moving to applications.
This page was last updated on 2026-08-01 and is reviewed periodically as new material appears.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
| Property | Value | Notes |
|---|---|---|
| Separation principle | Differential partitioning | Analytes distribute between mobile and stationary phases. |
| Mobile phase | Liquid solvent mixture | Composition controls retention and selectivity. |
| Stationary phase | Packed column particles | Often chemically bonded silica. |
| Typical detector | UV-Vis or photodiode array | Mass spectrometry is also common. |
| Common synonym | High-performance liquid chromatography | Abbreviated as HPLC. |
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
Validation demonstrates that a method is suitable for its intended use. Typical performance characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulators and standards organizations provide frameworks, but specific requirements depend on the application and jurisdiction. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, retention time repeatability, and sensitivity. A validated method is not permanently fixed; changes may require partial or full revalidation.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
HPLC testing separates dissolved compounds by passing a liquid sample through a column packed with stationary phase. A pump delivers mobile phase at controlled flow, and the sample components interact differently with stationary and mobile phases. Compounds that spend more time in mobile phase elute earlier; those retained by stationary phase elute later. Detectors record elution as peaks, and peak area or height relates to amount. This mechanism underpins quantitative analysis of mixtures.
Method validation examines whether an HPLC procedure is suitable for its intended purpose. Common parameters include accuracy, precision, specificity, linearity, range, detection limit, quantification limit, and robustness. Accuracy describes closeness to a true or accepted value, while precision describes agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from related substances. Robustness tests small deliberate changes in flow, temperature, or solvent composition. Validation is not a one-time event; methods may need partial revalidation after changes to instruments, columns, sample handling, or specification limits. Regulatory guidance provides frameworks, but some details remain method-specific.
Regulatory and pharmacopeial texts shape how HPLC testing is performed and documented. The International Council for Harmonisation provides validation guidance, while pharmacopeias publish general chromatography chapters and monographs for specific materials. Accreditation standards such as ISO/IEC 17025 address laboratory competence and traceability. Inspectors may review instrument qualification, analyst training, reference material control, and electronic records. Open questions include how best to validate methods for new complex products and how to handle automated data processing. Laboratories generally resolve these issues through risk assessment, method lifecycle management, and documented scientific justification.
Oxymatrine (matrine oxide, matrine N-oxide, matrine 1-oxide) is one of many quinolizidine alkaloid compounds extracted from the root of Sophora flavescens, a Chinese herb. It is very similar in structure to matrine, which has one less oxygen atom, and oxymatrine is partially metabolized to matrine in the human gut. Oxymatrine has a variety of effects in vitro and in animal models, including protection against apoptosis, tumor and fibrotic tissue development, and inflammation. Furthermore, oxymatrine has been shown to decrease cardiac ischemia (decreased blood perfusion), myocardial injury, arrhythmias (irregular heartbeats), and improve heart failure by increasing cardiac function.
Mephedrone, also known as 4-methylmethcathinone, 4-MMC, or 4-methylephedrone, is a synthetic stimulant drug belonging to the amphetamine and cathinone classes. It is commonly referred to by slang names such as drone, M-CAT, white magic, meow meow, and bubble. Chemically, it is similar to the cathinone compounds found in the khat plant, native to eastern Africa. Mephedrone is typically found in tablet or crystal form, and users may swallow, snort, or inject it. Its effects are similar to those of MDMA, amphetamines, and cocaine, producing euphoria and increased sociability. Mephedrone is rapidly absorbed, with a half-life of about two hours, and is primarily metabolized by CYP2D6 enzymes. Its effects are dose-dependent. Side effects can include cardiovascular changes and anxiety. Mephedrone was first synthesised in 1929 but remained relatively obscure until it was rediscovered around 1999–2000. At that time, it was legal to produce and possess in many countries. By 2000, mephedrone was available for sale on the Internet. By 2008, law enforcement agencies had become aware of the substance, and by 2010, it had been reported in most European countries, with significant prevalence in the United Kingdom. Mephedrone was first made illegal in Israel in 2008, followed by Sweden later that year. By 2010, many European countries had banned the substance, and in December of that year, the European Union ruled it illegal.
The longest known half-life of 2.2 × 1024 years of tellurium-128 was measured by the method of detecting its radiogenic daughter xenon-128; this has been used for other isotopes with noble-gas daughters and barium-130 has also been measured no other way. Another notable example is the only naturally occurring isotope of bismuth, bismuth-209, which has been predicted to be unstable with a very long half-life, but has been observed to decay. Because of their long half-lives, such isotopes are still found on Earth in various quantities, and together with the stable isotopes they are called primordial isotopes. For a list of primordial nuclides in order of half-life, see List of nuclides. 118 chemical elements are known to exist. The first 94 are found in nature, and the remainder of the discovered elements are artificially produced, with isotopes all known to be radioactive with relatively short half-lives (see below). The elements in this list are ordered according to the lifetime of their most stable isotope. Of these, three elements (bismuth, thorium, and uranium) are primordial because they have half-lives long enough to still be found on the Earth, while all the others are produced either by radioactive decay or are synthesized in laboratories and nuclear reactors. Only 13 of the 38 unstable elements have a known isotope with a half-life of at least 100 years. Every known isotope of the remaining 25 elements is highly radioactive; these are used in academic research and sometimes in industry and medicine.
=== Role in fetal lung === In the fetal lung, they are frequently located at the branching points of airway tubules, and in humans are present by 10 weeks gestation. Peptides and amines released by PNEC are involved in normal fetal lung development including branching morphogenesis. The best-characterized peptides are GRP, the mammalian form of bombesin, and CGRP; these substances exert direct mitogenic effects on epithelial cells and exhibit many properties akin to growth factors.
Sources: en.wikipedia.org
== Cell function and characteristics == Unlike other fibroblast cell types, dermal fibroblasts are far less likely to change into other cell types. For example, when a dermal fibroblast and a corneal fibroblasts are placed in the same concentrations of fibroblast growth factor, dermal fibroblast will not differentiate or change. As noted by Dr. J. Lewis and Dr. A. Johnson authors of Microbiology of the Cell, "fibroblasts from the skin are different" and behave differently from other fibroblast cells to identical chemical stimuli. Furthermore, dermal fibroblasts are less likely to replicate in either in vivo and in vitro environments than are other fibroblast types. Dermal fibroblasts require far higher concentrations of fibroblast growth factor (FGF) in order to undergo cell replication. Dermal fibroblasts are responsible for creating the ECM which organizes the stratified squamous epithelial cells of the epidermis into a unified tissue. Furthermore, dermal fibroblasts create long fibrous bands of connective tissue which anchor the skin to the fascia of the body. Therefore, without dermal fibroblasts, the largest and heaviest organ would not tightly adhere to body's frame.
The supplement creatine may be helpful for well-trained athletes to increase exercise performance and strength in relation with their dietary regimen. Other popular studies done on supplements include androstenedione, chromium, and ephedra. The findings show that there are no substantial benefits from the extra intake of these supplements, yet higher health risks and costs.
=== CO2 absorption === Hydrated products of Portland cement, such as concrete and mortars, slowly reabsorb atmospheric CO2 gas, which has been released during calcination in a kiln. This natural process, reversed to calcination, is called carbonation. As it depends on CO2 diffusion into the bulk of concrete, its rate depends on many parameters, such as environmental conditions and surface area exposed to the atmosphere. Carbonation is particularly significant at the latter stages of the concrete life - after demolition and crushing of the debris. It is estimated that nearly 30% of atmospheric CO2 generated by cement production is reabsorbed during the life-cycle of cement products. Carbonation process is considered as a mechanism of concrete degradation. It reduces pH of concrete that promotes reinforcement steel corrosion. However, as the product of Ca(OH)2 carbonation, CaCO3, occupies a greater volume, porosity of concrete reduces. This increases strength and hardness of concrete. There are proposals to reduce carbon footprint of hydraulic cement by adopting non-hydraulic cement, lime mortar, for certain applications. It reabsorbs some of the CO2 during hardening, and has a lower energy requirement in production than Portland cement. A few other attempts to increase absorption of carbon dioxide include cements based on magnesium (Sorel cement).
==== Inhaled substances (pneumoconiosis) ==== Inorganic Silicosis Asbestosis Berylliosis Industrial printing chemicals (e.g. carbon black, ink mist) Organic Hypersensitivity pneumonitis (extrinsic allergic alveolitis), representing approximately 15% of cases of ILD.
Substrate-level phosphorylation is a metabolic reaction that results in the production of ATP or GTP supported by the energy released from another high-energy bond that leads to phosphorylation of ADP or GDP to ATP or GTP (note that the reaction catalyzed by creatine kinase is not considered as "substrate-level phosphorylation"). This process uses some of the released chemical energy, namely the Gibbs free energy, to transfer a phosphoryl (PO3) group to ADP or GDP. Substrate-level phosphorylation occurs in glycolysis and in the citric acid cycle. Unlike oxidative phosphorylation, oxidation and phosphorylation are not coupled in the process of substrate-level phosphorylation, and reactive intermediates are most often gained in the course of oxidation processes in catabolism. Most ATP is generated by oxidative phosphorylation in aerobic or anaerobic respiration while substrate-level phosphorylation provides a quicker, less efficient source of ATP, independent of external electron acceptors. This is the case in human erythrocytes, which have no mitochondria, and in oxygen-depleted muscle. Substrate-level phosphorylation occurs in the cytoplasm of cells during glycolysis and in mitochondria during the Krebs cycle. In the pay-off phase of glycolysis, a net of 2 ATP are produced by substrate-level phosphorylation.
Sources: en.wikipedia.org
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.
Pressure drives the liquid mobile phase through a column packed with small particles. Without pressure, flow would be very slow or stop because the packed bed resists liquid movement. Modern pumps maintain a steady flow despite the resistance.
A chromatogram is a plot of detector signal against time after sample injection. Each peak represents a compound or group of compounds eluting from the column. Retention time and peak area are the main measurements read from the plot.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.