Everything below concerns detector. We keep the language plain, cite what the science says, and separate well-supported claims from open questions.
Updated 2026-06-03. Numbers and descriptions here follow the published literature rather than marketing material.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
Documentation and traceability are central to regulated HPLC testing. Records typically include instrument logs, column history, mobile-phase preparation, sample preparation, injection sequences, raw chromatograms, and audit trails. Electronic systems may require user access controls, time-stamped changes, and backup procedures. Training records show that analysts are qualified for assigned methods. Audits and inspections check whether written procedures match actual practice and whether deviations are documented. These controls support reproducibility and allow results to be reconstructed if questions arise later.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
| Property | Value | Notes |
|---|---|---|
| Accuracy | Recovery near 100% | Depends on acceptance criteria and matrix |
| Precision | Relative standard deviation | Often at or below 2% for replicate injections |
| Limit of detection | Signal-to-noise ratio 3:1 | Approximate and method-specific |
| Limit of quantitation | Signal-to-noise ratio 10:1 | Confirmed by precision and accuracy |
| Resolution | 1.5 or greater | Typical system suitability target |
High-performance liquid chromatography is an analytical technique that separates components of a liquid sample by passing it through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in interaction with the stationary phase cause analytes to migrate at different rates. Detectors record elution as peaks, and a data system converts signals into a chromatogram. The method is suited to compounds that dissolve in a liquid and are not volatile enough for gas chromatography.
Reversed-phase chromatography dominates modern HPLC testing, using a nonpolar stationary phase such as chemically bonded octadecyl groups and a polar mobile phase of water mixed with organic solvent. Analytes partition between the mobile and stationary phases according to hydrophobicity. Gradient elution changes the mobile phase composition over time to separate compounds with a wide range of retention. Isocratic elution keeps the composition constant and is simpler for routine assays. Column temperature, pH, and flow rate influence selectivity, peak shape, and retention time, so these parameters are controlled during a validated method.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. A diode array detector records full spectra across a wavelength range, which helps identify co-eluting peaks. Mass spectrometry provides mass-to-charge ratios and can confirm molecular identity at low concentrations. The choice of detector depends on analyte structure, required sensitivity, and whether quantitation or identification is the goal. No single detector works for every compound, and method development often compares responses before selecting one.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample. A pump moves a liquid mobile phase through a column packed with a solid stationary phase. Compounds interact differently with both phases and travel at different rates, leaving the column at distinct retention times. A detector records these arrivals as peaks on a chromatogram. The resulting pattern supports identification and quantification of substances in mixtures. Modern instruments use high pressure to force solvent through small particles, which improves speed and resolution compared with older low-pressure liquid chromatography methods.
Separation in HPLC depends on the chemistry of the stationary phase, the composition of the mobile phase, and the physical properties of the column. Reverse-phase separations use a nonpolar stationary phase and a polar mobile phase, and they are common for many organic compounds. Ion-exchange, size-exclusion, and normal-phase modes serve other classes of analytes. Gradient elution changes solvent strength over time, while isocratic elution holds it constant. Flow rate, temperature, particle size, and column length all influence peak shape and resolution. Detection may use ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry, depending on the analyte and the required sensitivity.
Routine HPLC testing compares a sample result with a calibration curve prepared from known reference standards. Peak area or peak height is plotted against concentration, and the curve is used to estimate unknown amounts. Retention time supports tentative identification when compared with a standard, though mass spectrometry or another confirmatory method may be needed for definitive identification. Pre-run checks verify repeatability, resolution, and peak symmetry before sample analysis. Limits of detection and quantification describe the smallest amounts that can be reliably observed or measured. Sample preparation, filtration, and degassing help prevent column damage and inconsistent results.
== Leidenfrost temperature and surface tension effects == The Leidenfrost temperature is the property of a given set of solid–liquid pair. The temperature of the solid surface beyond which the liquid undergoes the Leidenfrost phenomenon is termed the Leidenfrost temperature. Calculation of the Leidenfrost temperature involves the calculation of the minimum film boiling temperature of a fluid. Berenson obtained a relation for the minimum film boiling temperature from minimum heat flux arguments. While the equation for the minimum film boiling temperature, which can be found in the reference above, is quite complex, the features of it can be understood from a physical perspective. One critical parameter to consider is the surface tension. The proportional relationship between the minimum film boiling temperature and surface tension is to be expected, since fluids with higher surface tension need higher quantities of heat flux for the onset of nucleate boiling. Since film boiling occurs after nucleate boiling, the minimum temperature for film boiling should have a proportional dependence on the surface tension. Henry developed a model for the Leidenfrost phenomenon which includes transient wetting and microlayer evaporation. Since the Leidenfrost phenomenon is a special case of film boiling, the Leidenfrost temperature is related to the minimum film boiling temperature via a relation which factors in the properties of the solid being used.
=== 2008–2011: Black Gives Way to Blue and death of Mike Starr === Blabbermouth.net reported on September 5, 2008, that Alice in Chains would enter the studio that October to begin recording a new album for a summer 2009 release. On September 14, 2008, Alice in Chains performed at halftime during the Seattle Seahawks vs San Francisco 49ers game at the Qwest Field (now named Lumen Field ) in Seattle. The 12-minute performance for a crowd of 67,000 people featured a cover of Led Zeppelin's "Kashmir" accompanied by the Northwest Symphony Orchestra. In October 2008, Alice in Chains began recording its fourth studio album at the Foo Fighters' Studio 606 in Los Angeles with producer Nick Raskulinecz. The band did not have a record label at the time and the album was funded by Jerry Cantrell and Sean Kinney. At the Revolver Golden God Awards, Cantrell said that the group had finished recording on March 18, 2009, and were mixing the album for a September release. The recording process was completed on Cantrell's 43rd birthday and also the same day that William DuVall's son was born. In April 2009, it was reported that the new Alice in Chains album would be released by Virgin/EMI, making it the band's first label change in its 20-plus year career. David Benveniste and his Velvet Hammer Music & Management Group began co-managing the band with Susan Silver, marking the most recent change of management and latest development to date.
=== Tempe bongkrèk === Tempe bongkrèk is a variety of tempeh from Central Java, notably Banyumas. It is prepared with coconut dregs. This type of tempeh served as a main source of protein in Java due to its inexpensiveness and has led to several cases of fatal food poisoning, as it occasionally gets contaminated with the bacterium Burkholderia gladioli, and the unwanted organism produces toxins (bongkrek acid and toxoflavin) from the coconut, besides killing off the Rhizopus fungus due to the antibiotic activity of bongkrek acid. Fatalities from contaminated tempe bongkrèk were once common in the area where it was produced. During 1930s, the Dutch East Indies government went through an economic depression, and this condition caused some of the people to make tempe bongkrek by themselves, instead of buying it directly from well-trained producers. As a result, the poisonings occurred frequently, reaching 10 to 12 a year. Dutch scientists W. K. Mertens and A. G. van Veen from the Eijkman Institute of Jakarta, started to find the cause of the poisoning in the early 1930s. The first outbreak of the bongkrek poisoning by tempe bongkrek was recorded by Dutch researchers; however, no further research to find the cause of the poisoning was conducted in 1895. They successfully identified the source of poisoning as a bacterium called Pseudomonas marginata. This bacterium, which is also named Burkholderia cocovenenans, caused the synthesis of a poisonous substance called bongkrek acid. B.
Sources: en.wikipedia.org
=== In human plasma === HNPs have been extensively studied as plasma marker of a range of diseases such as atherosclerosis, rheumatic diseases, infections, cancer, preeclampsia, and schizophrenia. Antibodies directed against fully processed HNP-1 seem to have low affinity for the propeptides, proHNPs. A recent study used antibodies directed against proHNPs to show that the predominant forms of alpha-defensins in plasma are in fact proHNPs. ProHNPs are exclusively synthesized by neutrophil precursors in the bone marrow and appear to be very specific markers of granulopoiesis.
She delivered the exhibition Claude Bernard naturaliste (Claude Bernard, naturalist) in 1978, La bionique, science des inventions de la nature (Bionics, science of inventions of nature) in 1985, La géonomie, science de l'homme dans la nature en 1986, and le Bicentenaire de Buffon (the Bicentennial of Buffon) in 1988. From 1986, she was responsible for a series of temporary exhibitions including Parfums de plantes (Perfumes of plants), a collaboration between the museum and perfume and aromatics industry companies. At the same time, she wrote the synopsis for the Esquisse d'une planète habitée (Sketch of an Inhabited Planet) about genomics by Maxence Revault d'Allonnes and Jean-Pierre Gasc, and worked on the creation of the Musée des Sciences de la Terre (Museum of Earth Sciences) in Rabat, Morocco in collaboration with paleontologist Philippe Taquet.
== Applications == Because all primordial bismuth is bismuth-209, bismuth-209 is used for all normal applications of bismuth, such as being used as a replacement for lead, in cosmetics, in paints, and in several medicines such as Pepto-Bismol. Alloys containing bismuth-209 such as bismuth bronze have been used for thousands of years.
Sources: en.wikipedia.org
Validation establishes suitability for a new method, while verification confirms that a method works in a specific laboratory. Verification is often used when a validated method is adopted with existing equipment and staff. Both rely on documented acceptance criteria.
Quantification usually compares detector response to a standard curve made from reference standards. The curve may be external, internal, or based on standard addition depending on matrix effects. Results are reported with units and, when required, uncertainty.
Carryover occurs when analyte from a previous injection remains in the system and appears in a later chromatogram. It can come from the injector, column, or tubing. Blank injections and needle washes help detect and reduce it.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.