If you have been reading about Stationary phase and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2026-01-29. Where a claim depends on a specific study, the study is described rather than over-claimed.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
Quality control laboratories use HPLC to check identity, purity, concentration, and stability of raw materials and finished products. A validated method specifies the column, mobile phase, flow rate, detection wavelength, injection volume, and run time. Samples are prepared and compared against reference standards of known concentration. The resulting chromatogram provides quantitative data, such as assay values and impurity levels. This approach is common in pharmaceutical, food, environmental, and industrial testing where consistent measurements are required.
Method validation demonstrates that an analytical procedure is suitable for its intended purpose. Typical validation characteristics include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Regulatory guidance from bodies such as the International Council for Harmonisation and the United States Pharmacopeia outlines expectations, though specific criteria depend on the product and method. System suitability tests are run before sample analysis to confirm resolution, peak symmetry, column efficiency, and injection repeatability. Failure of these checks can invalidate a batch of measurements.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Measured value compared with true or accepted value |
| Precision type | Repeatability | Same analyst, instrument, and short time interval |
| Linearity range | 50–150% of target concentration | Common for assay methods; method-dependent |
| Limit of quantitation | Signal-to-noise ratio of 10:1 | Lowest concentration with acceptable precision |
| Common synonyms | Method validation, analytical validation | Documented confirmation that a method is suitable |
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Detection commonly uses ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. Ultraviolet detection depends on molecular chromophores that absorb light at specific wavelengths. Mass spectrometry provides mass information and sensitive quantification, often after electrospray ionization. Before sample batches, performance checks examine resolution, elution time repeatability, peak symmetry, and plate count. Matrix effects and co-elution remain recognized uncertainties; formal validation studies and orthogonal detection help address them. Detector choice depends on analyte properties and required sensitivity.
High-performance liquid chromatography, or HPLC, separates dissolved compounds by passing a liquid mobile phase through a packed column. Components distribute differently between the stationary phase and the moving liquid, so they travel at different speeds and exit at different times. A detector records these eluting bands as peaks, and peak area or height relates to amount. The technique supports testing in pharmaceuticals, foods, environmental samples, and industrial chemicals. Quantification usually depends on calibration with known standards.
Several separation modes exist, including reversed-phase, normal-phase, ion-exchange, size-exclusion, and hydrophilic interaction liquid chromatography. Reversed-phase uses a nonpolar stationary phase with a polar mobile phase and is widely applied to small organic molecules. Gradient elution changes mobile phase composition during the run, while isocratic elution keeps it constant. Column chemistry, particle size, temperature, flow rate, and mobile phase pH all influence retention and resolution. Method development selects conditions that separate analytes from matrix components and from each other.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
HPLC testing is not a single fixed procedure; it is a family of separation modes. Reversed-phase, normal-phase, ion-exchange, size-exclusion, and affinity chromatography each suit different analyte properties. Reversed-phase methods dominate because they handle many neutral and moderately polar compounds. Detection can be optical, electrochemical, or mass spectrometric, and the detector dictates what information is available. Coupling with mass spectrometry increases selectivity and enables identification when standards are unavailable. The technique cannot separate every mixture without adjustment.
HPLC testing is an analytical technique used to separate, identify, and quantify components in a liquid sample. It relies on a pressurized mobile phase that carries the sample through a column packed with stationary phase. Different compounds travel at different rates because of interactions with the stationary and mobile phases. The resulting signal versus time is a chromatogram. Peak position indicates identity under specified conditions, while peak area or height relates to amount.
Laboratories apply HPLC testing across pharmaceutical, food, environmental, and industrial chemistry. The method can measure active ingredients, impurities, additives, preservatives, and degradation products. Sample preparation often includes dilution, filtration, and sometimes extraction or derivatization. The choice of column, mobile phase, pH, temperature, and detector depends on the analytes and matrix. Results are compared with reference standards to assign identity and concentration. Method suitability is judged by resolution, precision, and accuracy.
In the past, the People's Republic of China executed prisoners primarily by means of shooting. Recently, lethal injection has become more common. The specific lethal injection procedures, including the drug or drugs used, are a state secret and not publicly known. Lethal injection in China was legalized in 1996. The number of shooting executions slowly decreased, and in February 2009, the Supreme People's Court ordered the discontinuation of firing squads by the following year under the conclusion that injections were more humane to the prisoner. It has been suggested that the switch is also in response to executions being horrifying to the public. Lethal injections are less expensive than firing squads, with a single dose costing 300 yuan compared to 700 yuan for a shooting execution.
== Prevention == The American College of Obstetricians and Gynecologists recommends all people thinking of becoming pregnant be tested to see if they have thalassemia. Genetic counseling and genetic testing are recommended for families who carry a thalassemia trait. Understanding the genetic risk, ideally before a family is started, would hopefully allow families to understand more about the condition and make an informed decision that is best for their family. A screening policy exists in Cyprus to reduce the rate of thalassemia, which, since the program's implementation in the 1970s (also including prenatal screening and abortion), has reduced the number of children born with the disease from one of every 158 births to almost zero. Greece also has a screening program to identify people who are carriers. In Iran as a premarital screening, the man's red cell indices are checked first. If he has microcytosis (mean cell hemoglobin < 27 pg or mean red cell volume < 80 fl), the woman is tested. When both are microcytic, their hemoglobin A2 concentrations are measured. If both have a concentration above 3.5% (diagnostic of thalassemia trait) they are referred to the local designated health post for genetic counseling. Large-scale awareness campaigns are being organized in India both by government and non-government organizations to promote voluntary premarital screening, with marriage between carriers strongly discouraged.
In September 2023, the FDA approved a two-component therapy of Pombiliti (cipaglucosidase alfa-atga) and Opfolda (miglustat) 65 mg capsules for adults living with late-onset Pompe disease weighing more than 40 kg and who are not improving on their current enzyme replacement therapy. However, even with combination therapy, it remains unclear whether long-term symptoms of Pompe disease can be adequately mitigated. Criticallly, the tissues most affected, namely the central nervous system (CNS) and skeletal muscles, are notoriously difficult to target with ERT. As a result, efforts to identify alternative approaches have increasingly focused on tissue-targeted strategies and substrate reduction therapies, which may enhance delivery to skeletal muscles and facilitate crossing of the blood-brain barrier, thereby improving CNS uptake.
Sources: en.wikipedia.org
In addition to psychedelics being defined as controlled substances at the federal level, individual U.S. states, such as Alabama, may also make psychedelics controlled substances within their jurisdictions. Conversely, state-level and lower jurisdictions may alternatively legalize or decriminalize psychedelics, for instance Colorado and Oregon and individual cities like San Francisco. This can result in legal conflict and ambiguity at different levels of government, for example a given drug being illegal at the federal level but legal at the state level.
==== Possible prebiotic environments ==== The symmetry-breaking and chiral amplification of racemic RAO only requires a prebiotic environment where RAO is available and can interact with spin-polarized magnetic surfaces. One suggested environment is an evaporative lake with magnetic sediments, such as magnetite or greigite, which gain a statistically uniform net magnetization on a hemisphere scale from the Earth's geomagnetic field. These environments could have been widespread on the early Earth, and wet-drying cycling within and at the edges of these lakes could facilitate both crystallization and replenishment of RAO, along with other prebiotic precursors important for early life.
The AAA pathway involves the condensation of α-ketoglutarate and acetyl-CoA via the intermediate AAA for the synthesis of L-lysine. This pathway has been shown to be present in several yeast species, as well as protists and higher fungi. It has also been reported that an alternative variant of the AAA route has been found in Thermus thermophilus and Pyrococcus horikoshii, which could indicate that this pathway is more widely spread in prokaryotes than originally proposed. The first and rate-limiting step in the AAA pathway is the condensation reaction between acetyl-CoA and α‑ketoglutarate catalysed by homocitrate-synthase (HCS) (E.C 2.3.3.14) to give the intermediate homocitryl‑CoA, which is hydrolysed by the same enzyme to produce homocitrate. Homocitrate is enzymatically dehydrated by homoaconitase (HAc) (E.C 4.2.1.36) to yield cis-homoaconitate. HAc then catalyses a second reaction in which cis-homoaconitate undergoes rehydration to produce homoisocitrate. The resulting product undergoes an oxidative decarboxylation by homoisocitrate dehydrogenase (HIDH) (E.C 1.1.1.87) to yield α‑ketoadipate. AAA is then formed via a pyridoxal 5′-phosphate (PLP)-dependent aminotransferase (PLP-AT) (E.C 2.6.1.39), using glutamate as the amino donor. From this point on, the AAA pathway varies with [something is missing here ? -> at the very least, section header! ] on the kingdom.
=== Tissue engineering === The ability of SHG to image specific molecules can reveal the structure of a certain tissue one material at a time, and at various scales (from macro to micro) using microscopy. For instance, the collagen (type I) is specifically imaged from the extracellular matrix (ECM) of cells, or when it serves as a scaffold or conjonctive material in tissues. SHG also reveals fibroin in silk, myosin in muscles and biosynthetized cellulose. All of this imaging capability can be used to design artificials tissues, by targeting specific points of the tissue : SHG can indeed quantitatively measure some orientations, and material quantity and arrangement. Also, SHG coupled to other multiphoton techniques can serve to monitor the development of engineered tissues, when the sample is relatively thin however. Of course, they can finally be used as a quality control of the fabricated tissues.
Sources: en.wikipedia.org
Impaired oral tolerance Gut dysbiosis Increased gut permeability Heightened immune reactivity Chemicals, which are either a part of the immediate environment or found in drugs, are key players in this context. Examples of such chemicals include hydrazines, hair dyes, trichloroethylene, tartrazines, hazardous wastes, and industrial emissions. Ultraviolet radiation has been implicated as a potential causative factor in the development of autoimmune diseases, such as dermatomyositis. Furthermore, exposure to pesticides has been linked with an increased risk of developing rheumatoid arthritis. Vitamin D, on the other hand, appears to play a protective role, particularly in older populations, by preventing immune dysfunctions. Infectious agents are also being increasingly recognized for their role as T cell activators — a crucial step in triggering autoimmune diseases. The exact mechanisms by which they contribute to disease onset remain to be fully understood. For instance, certain autoimmune conditions like Guillain-Barre syndrome and rheumatic fever are thought to be triggered by infections. Furthermore, analysis of large-scale data has revealed a significant link between SARS-CoV-2 infection (the causative agent of COVID-19) and an increased risk of developing a wide range of new-onset autoimmune diseases.
==== Synthetic ==== The cancellous part of bones contain bone marrow. Bone marrow produces blood cells in a process called hematopoiesis. Blood cells that are created in bone marrow include red blood cells, platelets and white blood cells. Progenitor cells such as the hematopoietic stem cell divide in a process called mitosis to produce precursor cells. These include precursors which eventually give rise to white blood cells, and erythroblasts which give rise to red blood cells. Unlike red and white blood cells, created by mitosis, platelets are shed from very large cells called megakaryocytes. This process of progressive differentiation occurs within the bone marrow. After the cells are matured, they enter the circulation. Every day, over 2.5 billion red blood cells and platelets, and 50–100 billion granulocytes are produced in this way. As well as creating cells, bone marrow is also one of the major sites where defective or aged red blood cells are destroyed.
=== Dressings and topical silicone === Silicone scar treatments are commonly used in preventing scar formation and improving existing scar appearance. A meta-study by the Cochrane collaboration found weak evidence that silicone gel sheeting helps prevent scarring. However, the studies examining it were of poor quality and susceptible to bias. Pressure dressings are commonly used in managing burn and hypertrophic scars, although supporting evidence is lacking. Care providers commonly report improvements, however, and pressure therapy has been effective in treating ear keloids. The general acceptance of the treatment as effective may prevent it from being further studied in clinical trials.
Iridium-192 (symbol 192Ir) is a radioactive isotope of iridium, with a half-life of 73.82 days. It decays by emitting beta (β) particles and gamma (γ) radiation. 95.24% of 192Ir decays occur via β- emission, leading to 192Pt; the remaining 4.76% occur via electron capture to 192Os; both modes involve gamma emission. Iridium-192 is normally produced by neutron activation of natural-abundance iridium metal. Iridium-192 is a very strong gamma ray emitter, with a gamma dose constant of 1.54 μSv·h−1·MBq−1 at 30 cm, and a specific activity of 341 TBq·g−1 (9.22 kCi·g−1). There are seven principal gamma rays produced in its beta-minus decay, ranging from 296.0 to 612.5 keV, and two produced in its electron capture decay at 205.8 and 484.6 keV. It is commonly used as a gamma ray source in industrial radiography to locate flaws in metal components. It is also used in radiotherapy as a radiation source, in particular in brachytherapy. Iridium-192 has accounted for the majority of cases tracked by the U.S. Nuclear Regulatory Commission in which radioactive materials have gone missing in quantities large enough to make a dirty bomb. The metastable isomer 192m2Ir is iridium's most stable isomer. It decays solely by isomeric transition (to this ground state) with a half-life of 241 years, which is somewhat unusual for its long half-life and that said half-life greatly exceeds that of the ground state.
== Protein identification via sequence database searching == Sequence database searching is widely used currently for mass spectra based protein identification. In this approach, a protein sequence database is used to calculate all putative peptide candidates in the given setting (proteolytic enzymes, miscleavages, post-translational modifications). The sequence search engines use various heuristics to predict the fragmentation pattern of each peptide candidate. Such derivative patterns are used as templates to find a sufficiently close match within experimental mass spectra, which serves as the basis for peptide/protein identification. Many tools have been developed for this practice, which have enabled many past discoveries, e.g. SEQUEST, Mascot.
Sources: en.wikipedia.org
System suitability is a set of checks that confirm the instrument and method perform within limits before sample analysis. It typically includes resolution, tailing factor, retention time, and peak area reproducibility. If a check fails, the run is invalidated until the cause is resolved.
QC samples are usually injected at the beginning, at intervals during the run, and at the end. The exact frequency depends on the method, sample count, and regulatory requirements. Results outside acceptance limits can require rejection of the affected samples and investigation.
Method validation demonstrates that an HPLC procedure produces reliable results for its intended purpose. It provides documented evidence for accuracy, precision, specificity, and other performance characteristics. Regulators and quality systems require validation before a method is used for release or stability testing.
Method validation is the documented process of confirming that an HPLC procedure is suitable for its intended use. It evaluates accuracy, precision, specificity, linearity, range, detection limits, and robustness. Validation criteria depend on the regulatory context and the sample type.