If you have been reading about Quality control and want a single page that covers the useful parts, this is it: definitions, context, how it is studied, and the questions that come up repeatedly.
Last reviewed on 2025-11-03. Where a claim depends on a specific study, the study is described rather than over-claimed.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
Validation establishes that a method is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, robustness, and stability of standards and samples. Acceptance criteria are defined in advance, and results are documented in a validation report. Regulatory guidance for pharmaceuticals, foods, and environmental testing differs, so the applicable framework must be identified. Ongoing verification uses control samples and trend charts after validation. Method transfer to another laboratory may require partial revalidation.
Routine quality control includes blanks, duplicates, spiked samples, and certified reference materials. Calibration curves are prepared with standards at several concentrations, and the detector response is checked for linearity. Carryover, column aging, mobile phase evaporation, and temperature drift can shift retention times or peak areas. Maintenance such as replacing seals, filters, and columns helps prevent failures. Records of injections, integration, and deviations support traceability. Audits may request raw data and instrument logs for each batch.
Developing an HPLC test begins with defining the analytes, matrix, and required reporting limits. Chemists select a separation mode, column chemistry, mobile phase composition, flow rate, and detection wavelength or mass transition. Experiments then adjust these variables to achieve adequate retention, resolution, and peak shape. System suitability tests confirm that the instrument and method perform consistently before sample analysis. Without suitable resolution, quantitative results may be unreliable. Preliminary runs often use scouting gradients to locate retention windows.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness of measured value to accepted reference value |
| Validation parameter | Precision | Agreement among repeated measurements under specified conditions |
| System suitability check | Resolution ≥ 1.5 | Baseline separation between critical peak pair |
| System suitability check | Tailing factor ≤ 2.0 | Common target for peak symmetry |
| Documentation | Validation report | Summarizes experiments, acceptance criteria, and conclusions |
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Quality control for HPLC testing combines scheduled checks, documented procedures, and review of results. Before sample analysis, system suitability testing confirms that the instrument, column, and method meet predefined criteria. Common criteria include resolution between critical peaks, retention time precision, peak tailing, and theoretical plate count. Failure triggers investigation before results are reported. Records link raw data, calculations, instrument logs, and analyst identity to each batch, supporting audits and repeat analysis.
Method validation evaluates accuracy, precision, specificity, linearity, range, detection limit, quantitation limit, and robustness. Regulatory guidance for pharmaceuticals, foods, and environmental testing defines expected documentation and acceptance criteria. Verification confirms that a validated method works in a specific laboratory with its own instruments and reagents. Calibration curves use reference standards with known purity and traceability, while measurement uncertainty is estimated from validation data, control charts, and collaborative studies. The scope of validation depends on the method's intended use.
Routine quality control monitors retention time shifts, baseline noise, system pressure, and peak shape. Trends can reveal column aging, mobile phase preparation errors, detector drift, or sample degradation. Corrective actions may include replacing the column, preparing fresh mobile phase, or recalibrating the detector. Stability testing often uses HPLC to measure parent compound loss and degradation product formation. Open questions remain about how accelerated stability results extrapolate to long-term storage under varied conditions.
Method validation establishes that an HPLC procedure is suitable for its intended purpose. Typical parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, robustness, and solution stability. Accuracy reflects closeness to a reference value, while precision reflects agreement among repeated measurements. Specificity shows whether the method can measure the analyte without interference from matrix components. Validation is documented through protocols and reports, and the required extent depends on the method's use and regulatory context.
Routine quality control uses system suitability, blank injections, check standards, and control samples to detect drift or contamination. System suitability criteria may specify minimum resolution, maximum tailing factor, and a permitted range for repeated injections. Blank injections reveal carryover or solvent contamination, while check standards confirm calibration accuracy over a batch. Control samples with known analyte levels can show whether results remain within statistical limits. When a control result falls outside limits, the analyst investigates the cause and may invalidate affected results before repeating the batch.
In 1969, Wenger was recruited to nearby third division club Mutzig. The club was famed for playing the "best amateur football" in Alsace and managed by Max Hild, who would later go on to become Wenger's mentor. Wenger's emergence at Mutzig aged 20 was considered too late for him to build a reputable playing career. Football was not seen as his future; the plan was for him to run the family's spare parts business. He was, however, of the age to start increasing his tactical knowledge of the sport. He frequently read France Football and alongside Hild made trips to Germany to watch Bundesliga matches and observe the different managerial styles. During Wenger's three years at Mutzig, the club beat Strasbourg 3–0 to win the Coupe d'Alsace. He also represented Alsace in a competition held annually between the regional leagues. Wenger took his studies further, and in 1971 enrolled at the Faculté des sciences économiques et de gestion (Faculty of Economic and Management Sciences) at the University of Strasbourg to read politics and economics after a brief stint in medicine. In 1973 he joined semi-professional club Mulhouse and balanced his football career with his education. Wenger completed an economics degree a year later. He was selected to represent the national French students squad and visited Nigeria, Lebanon, and Uruguay – where the World Students Championship was held in 1976.
By that time, internal political life in Serbia was fully dominated by the Communist Party of Serbia, formed in May 1945 as a branch of the ruling Communist Party of Yugoslavia. In order to suppress remaining monarchist opposition, communists initiated the creation of a wider political coalition, thus establishing the People's Front of Yugoslavia (PFY), in August 1945. Other political parties were soon dissolved, and remnants of political life were constrained within the PFY, that was under full control of the ruling Communist Party.
=== Locomotion === The female worker ants do not have wings and reproductive females lose their wings after their mating flights in order to begin their colonies. Therefore, unlike their wasp ancestors, most ants travel by walking. Some species are capable of leaping. For example, Jerdon's jumping ant (Harpegnathos saltator) is able to jump by synchronising the action of its mid and hind pairs of legs. There are several species of gliding ant including Cephalotes atratus; this may be a common trait among arboreal ants with small colonies. Ants with this ability are able to control their horizontal movement so as to catch tree trunks when they fall from atop the forest canopy.
== External links == Target+Peptide at the U.S. National Library of Medicine Medical Subject Headings (MeSH) SPdb (Signal Peptide DataBase) Archived 2016-01-22 at the Wayback Machine Prediction methods: SignalP — predicts the presence and location of signal peptide cleavage sites in amino acid sequences from all domains of organisms. PHOBIUS - combined transmembrane topology and signal peptide predictor
Sources: en.wikipedia.org
In 1985, Kidder expressed ambivalence toward continuing her career, and was quoted as saying: "I don't feel comfortable as a performer and I'm a big turkey as a movie star." She stated that the quote was reported out of context, but conceded: "I am in a weird frame of mind at the moment. I know acting is not going to be enough for me for the rest of my life. This business is very hard on women at a certain age, and I never want to end up just having to accept what's offered me. So, I am anxious to direct, to have options." In 1986, she was selected as the English narrator for the Japanese animated series The Wonderful Wizard of Oz. In 1987, Kidder reprised her Lois Lane role in Superman IV: The Quest for Peace (1987), which she filmed in 1986. Body of Evidence (1988), a CBS Movie of the Week, cast Kidder as a nurse who suspects that her medical pathologist husband is a serial killer.
A December 2024 report by Amnesty International found the use of unguided missiles on civilian areas to likely constitute indiscriminate attacks. International humanitarian law states that parties in a conflict must not direct attacks at civilians and must distinguish civilians and civilian infrastructure from military targets.
Wheeler was awarded the Lab on a Chip Pioneers in Miniaturization Award (2017), an E.W.R. Steacie Fellowship from the Natural Sciences and Engineering Research Council of Canada (NSERC) (2015), a Connaught Foundation McLean Fellowship (2014), the Joseph Black Award from the Royal Society of Chemistry (2012), the Arthur F. Findeis Award from the American Chemical Society (2012), the Young Innovator Award in Analytical Chemistry (2011), and a Sloan Research Fellowship (2009). In January 2024, Wheeler was honored with the Ricardo Aroca Award, recognizing his contributions to analytical chemistry and advancing lab-on-a-chip techniques, particularly through the use of digital microfluidics (DMF), which enables precise manipulation of liquid droplets on electrode arrays. The Award is bestowed upon a scientist living in Canada who has made a notable contribution to the discipline of analytical chemistry while conducting research within the country.
Sources: en.wikipedia.org
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.
Validation follows a planned protocol that tests accuracy, precision, specificity, linearity, range, detection limits, quantitation limits, and robustness. Results are compared against predefined acceptance criteria. The validation report supports regulatory filing or routine use.
Revalidation may be needed after changes to column chemistry, mobile phase, detection, sample preparation, or instrument type. It can also follow a pattern of out-of-specification results. The scope depends on whether the change affects method performance.
System suitability is a set of checks performed before and during a run to confirm that the instrument, column, and method work as expected. Common checks include resolution, tailing factor, theoretical plates, and relative standard deviation of replicate injections. Failure triggers troubleshooting or method adjustment.