accuracy comes up often in conversation and rarely with the context attached. Here we lay out the basics in order, then work through the practical considerations.
Updated 2026-04-15. Numbers and descriptions here follow the published literature rather than marketing material.
Most routine HPLC testing uses reversed-phase columns, where the stationary phase is nonpolar and the mobile phase is a polar mixture such as water with an organic solvent. Analytes partition between the two phases according to polarity, size, and charge. Gradients that change solvent composition over time can separate compounds with broad retention ranges. Isocratic conditions keep solvent composition constant and suit simpler mixtures. The choice of column chemistry, pH, and temperature affects selectivity and peak shape.
Detection in HPLC testing commonly relies on ultraviolet-visible absorbance, fluorescence, refractive index, or mass spectrometry. UV detection is widely used because many organic compounds absorb light, but it requires a chromophore. Mass spectrometry provides mass-based identification and high sensitivity for trace analytes. Each detector has trade-offs in selectivity, cost, and compatibility with mobile phases. Quantification typically uses calibration curves prepared from reference standards. Results are reported as concentration, purity, or presence above a limit.
High-performance liquid chromatography is an analytical technique that separates components in a liquid sample by passing them through a packed column under pressure. A pump delivers a mobile phase at a controlled flow rate, and an injector introduces the sample into the stream. Differences in how analytes partition between the mobile phase and the stationary phase cause them to exit the column at different times. Detection then records a signal proportional to the amount of each separated substance. The resulting chromatogram provides retention times and peak areas for identification and quantification.
Instrumentation includes a solvent delivery system, an autosampler, a column oven, and one or more detectors. Reversed-phase columns with chemically modified silica are widely used, but normal-phase, ion-exchange, size-exclusion, and affinity modes exist for specific separations. Detectors may rely on ultraviolet absorbance, fluorescence, refractive index, or mass spectrometry. Column temperature, mobile phase composition, and flow rate are adjusted to improve resolution. System pressure is monitored because rising pressure can indicate column blockage or deteriorating packing.
Separation performance depends on particle size, pore size, column length, and the chemistry of the stationary phase. Smaller particles generally improve efficiency but require higher pressure and suitable instrumentation. The mobile phase often contains buffers and organic solvents that influence retention and selectivity. Testing labs select conditions based on the analytes, sample matrix, and required sensitivity. Method development frequently involves screening several columns and solvent mixtures before a final set of conditions is chosen.
| Property | Value | Notes |
|---|---|---|
| Separation mode | Reversed-phase | Nonpolar stationary phase with polar mobile phase |
| Typical column particle size | 3–5 µm | Smaller particles improve resolution but raise pressure |
| Typical flow rate | 0.5–2.0 mL/min | Depends on column dimensions and pressure limits |
| Common detection | UV-Vis absorbance | Requires analytes with chromophores |
| Typical run time | 5–30 min | Varies with method, gradient, and sample complexity |
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
== Alanine world hypothesis == Alanine is one of the twenty canonical α-amino acids used as building blocks (monomers) for the ribosome-mediated biosynthesis of proteins. Alanine is believed to be one of the earliest amino acids to be included in the genetic code standard repertoire. On the basis of this fact the "alanine world" hypothesis was proposed. This hypothesis explains the evolutionary choice of amino acids in the repertoire of the genetic code from a chemical point of view. In this model the selection of monomers (i.e. amino acids) for ribosomal protein synthesis is rather limited to those alanine derivatives that are suitable for building α-helix or β-sheet secondary structural elements. Dominant secondary structures in life as we know it are α-helices and β-sheets and most canonical amino acids can be regarded as chemical derivatives of alanine. Therefore, most canonical amino acids in proteins can be exchanged with alanine by point mutations while the secondary structure remains intact. The fact that alanine mimics the secondary structure preferences of the majority of the encoded amino acids is practically exploited in alanine scanning mutagenesis. In addition, classical X-ray crystallography often employs the polyalanine-backbone model to determine three-dimensional structures of proteins using molecular replacement—a model-based phasing method.
== Regulatory history == The device was evaluated under an investigational device exemption in the United States, where it was compared against transforaminal lumbar interbody fusion. It was later granted FDA Breakthrough Device designation in 2021, followed by full FDA approval in 2023 after demonstrating superiority over fusion in composite clinical success. The TOPS System also holds CE marking, signifying that it meets health, safety, and environmental requirements for sale in the European Economic Area.
=== RNA editing in plant mitochondria and plastids === It has been shown in previous studies that the only types of RNA editing seen in the plants' mitochondria and plastids are conversion of C-to-U and U-to-C (very rare). RNA-editing sites are found mainly in the coding regions of mRNA, introns, and other non-translated regions. In fact, RNA editing can restore the functionality of tRNA molecules. The editing sites are found primarily upstream of mitochondrial or plastid RNAs. While the specific positions for C to U RNA editing events have been fairly well studied in both the mitochondrion and plastid, the identity and organization of all proteins comprising the editosome have yet to be established. Members of the expansive PPR protein family have been shown to function as trans-acting factors for RNA sequence recognition. Specific members of the MORF (Multiple Organellar RNA editing Factor) family are also required for proper editing at several sites. As some of these MORF proteins have been shown to interact with members of the PPR family, it is possible MORF proteins are components of the editosome complex. An enzyme responsible for the trans- or deamination of the RNA transcript remains elusive, though it has been proposed that the PPR proteins may serve this function as well. RNA editing is essential for the normal functioning of the plant's translation and respiration activity. Editing can restore the essential base-pairing sequences of tRNAs, restoring functionality.
Sources: en.wikipedia.org
== Diagnosis == One of the most important factors used to determine the clinical suspicion of malignancy of an adnexal mass is the sonographic (ultrasound) appearance of the mass. Indications that the mass is at a higher risk of being malignant include the presence of loculations, nodules, papillary structures, septations, or a size greater than 10 cm.
Over the first three-quarters of the 19th century, many experimenters worked with various combinations of platinum or iridium wires, carbon rods, and evacuated or semi-evacuated enclosures. Many of these devices were demonstrated and some were patented. In 1835, James Bowman Lindsay demonstrated a constant electric light at a public meeting in Dundee, Scotland. He stated that he could "read a book at a distance of one and a half feet". However he did not develop the electric light any further. In 1838, Belgian lithographer Marcellin Jobard invented an incandescent light bulb with a vacuum atmosphere using a carbon filament. In 1840, British scientist Warren De la Rue enclosed a coiled platinum filament in a vacuum tube and passed an electric current through it. The design was based on the concept that the high melting point of platinum would allow it to operate at high temperatures and that the evacuated chamber would contain fewer gas molecules to react with the platinum, improving its longevity. Although a workable design, the cost of the platinum made it impractical for commercial use. In 1841, Frederick de Moleyns of England was granted the first patent for an incandescent lamp, with a design using platinum wires contained within a vacuum bulb. He also used carbon. In 1845, American John W. Starr patented an incandescent light bulb using carbon filaments. His invention was never produced commercially. In 1851, Jean Eugène Robert-Houdin publicly demonstrated incandescent light bulbs on his estate in Blois, France.
Grand Master Filema Duarte then stripped former Grand Master Urquía Carreño of all his Masonic rights, and referred him to appear in front of the Supreme Court of Masonic Justice, so that they could review the case. On September 10, 2024, Urquía Carreño was then arrested and taken into custody by the National Revolutionary Police at Zanja y Dragones Police Station, the same police station which had launched the theft investigation on January 12. His official charge was the embezzlement of $MN754,410.54 and US$2,700. Urquía Carreño and Airam Cervera were given a travel limit by the Cuban government, prevented from leaving the island with any potential stolen cash. In 2025, Urquía Carreño gave an interview on a YouTube channel associated with the Cuban government in which he denied all wrongdoing, and reiterated his belief that Viñas Alonso was the leader of an anti-government conspiracy alongside Gerardo Cepero and Ángel Santiesteban to remove him from office. He insisted that everything had been orchestrated by this group, beginning with the theft and ending with Urquía Carreño's eventual resignation.
Sources: en.wikipedia.org
It separates components in a liquid sample and measures their amounts using a detector. Results can indicate concentration, purity, or identity based on retention time and detector response. The technique works for mixtures that can be dissolved and filtered.
It offers high resolution, reproducibility, and compatibility with many sample types. A single run can separate and quantify multiple analytes. It is common in pharmaceutical, food, environmental, and industrial laboratories.
Samples must be soluble in a suitable mobile phase and free of particles that can block the column. Detector response depends on analyte structure, so some compounds need derivatization or alternative detection. Complex matrices may require extensive sample preparation.
HPLC separates and detects individual compounds in a liquid sample, producing peaks at characteristic retention times. Peak area or height can be used to estimate concentration when calibrated with known standards. It does not identify unknown compounds with certainty unless additional detectors or reference materials are used.