This is a working overview of mobile phase, written for readers who want more than a one-paragraph summary but less than a textbook.
Reviewed 2026-06-28. Anything still debated is marked as such rather than presented as settled.
Quality control samples are inserted at intervals to monitor accuracy and precision throughout a batch. Blank samples detect contamination, while spiked samples assess recovery from the sample matrix. Calibration standards establish the relationship between detector response and concentration, and control samples are prepared independently from them whenever possible. Laboratories also participate in proficiency testing and maintain audit trails, instrument logs, and reagent records. Ongoing review of control charts can reveal trends before they cause out-of-specification results.
Method validation demonstrates that an HPLC procedure is suitable for its intended purpose. Common validation parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantification, and robustness. Accuracy reflects agreement with a reference value, while precision describes repeatability under defined conditions. Specificity shows whether the method can measure the analyte in the presence of impurities or matrix components. Validation documents are reviewed before a method is used for routine testing or regulatory submissions.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Typical checks include retention time, peak area precision, resolution between critical pairs, tailing factor, and theoretical plate count. Acceptance criteria are set in the method or pharmacopeial monograph. If a suitability check fails, the run may be rejected and the instrument or sample preparation may need investigation. This practice helps prevent release of data from a system that has drifted out of control.
Routine HPLC testing depends on controlled reagents, calibrated instruments, and documented procedures. Columns degrade over time, so retention times and peak shapes are monitored for drift. Mobile phases are filtered and degassed to prevent pump damage and detector noise. Reference standards must be traceable and stored under suitable conditions. Data handling systems record injections, calculations, and audit trails. Quality control samples interspersed with unknowns help detect errors during a run.
Developing an HPLC method begins with defining the purpose, such as quantifying a main component, measuring impurities, or confirming identity. Analysts select separation mode, column, mobile phase, detection, and sample preparation based on analyte properties and matrix. Experiments vary solvent strength, pH, buffer type, and temperature to achieve resolution between critical peaks. The goal is a robust method that produces reliable results across instruments and operators. Method development often involves trial runs and statistical optimization.
| Property | Value | Notes |
|---|---|---|
| Validation parameter | Accuracy | Closeness to a reference value. |
| Validation parameter | Precision | Repeatability or intermediate precision. |
| Validation parameter | Linearity | Proportional response across a range. |
| System suitability check | Resolution | Separation between adjacent peaks. |
| Quality control tool | Control chart | Tracks results over time for trends. |
Data handling and documentation are central to HPLC quality control. Electronic systems should have audit trails that record changes to methods, sequences, and results. Integration parameters, such as peak baseline and threshold, can affect reported areas and must be defined in advance. Out-of-specification results trigger a structured investigation that may include reanalysis, instrument checks, and review of sample preparation. Regulatory inspections often examine raw data, audit trails, and training records to verify that reported results are traceable and reliable.
Method validation establishes that an HPLC procedure is suitable for its intended use. Key parameters include accuracy, precision, specificity, linearity, range, limit of detection, limit of quantitation, and robustness. Accuracy measures agreement with a true or accepted value, while precision describes repeatability and intermediate precision. Specificity confirms that the method measures the analyte without interference from impurities, degradants, or excipients. Validation is documented in a protocol and report, and acceptance criteria are set before experiments begin. Regulatory guidance varies by region, but the general principles are widely harmonized.
System suitability testing is performed before and during analytical runs to confirm that the instrument and method are working as expected. Common checks include retention time, peak area, resolution between critical pairs, tailing factor, and theoretical plate count. Results are compared with predefined limits, and a failed check requires investigation before sample results are reported. Quality control samples at low, middle, and high concentrations are injected at intervals to monitor accuracy and precision. Blank injections detect carryover and contamination, while control charts track performance over time.
Separation modes differ by the chemistry of the stationary phase and the composition of the mobile phase. Reversed-phase testing uses a nonpolar column and polar solvents, making it common for pharmaceutical, environmental, and food analytes. Normal-phase testing uses a polar column and nonpolar solvents for compounds that are poorly retained in reversed-phase systems. Ion-exchange and ion-pair methods separate charged species, while size-exclusion methods sort molecules by hydrodynamic volume. Gradient elution changes solvent strength over time to resolve complex mixtures, and isocratic elution holds solvent composition constant for simpler assays.
Key performance measures include retention time, peak area, peak height, resolution, tailing factor, and plate count. Retention time helps identify a peak under fixed conditions, but confirmation often requires a second method or detector. Peak area and height relate to concentration through calibration curves, which may be linear or nonlinear depending on the detector response. Resolution describes separation between adjacent peaks, while tailing factor and plate count describe peak shape and column efficiency. Performance checks verify these values before and during a run to confirm that the instrument is performing within limits.
High-performance liquid chromatography testing separates components of a liquid sample by forcing a mobile phase through a packed column. The stationary phase inside the column interacts with analytes to different degrees, so each compound exits at a characteristic retention time. A pump delivers solvent at controlled flow and pressure, while an injector introduces a precise sample volume. Detectors such as ultraviolet-visible, fluorescence, refractive index, or mass spectrometric instruments record the separated bands. The resulting chromatogram provides qualitative and quantitative information about the mixture.
On November 21, 2006, EPA ordered DuPont to offer alternative drinking water or treatment for public or private water users living near DuPont's Washington Works plant in West Virginia (and in Ohio), if the level of PFOA detected in drinking water is equal to or greater than 0.5 parts per billion. This measure sharply lowered the previous action level of 150 parts per billion that was established in March 2002. According to a May 23, 2007, Environmental Science & Technology Online article, U.S. Food and Drug Administration research regarding food contact papers as a potential source of PFOA to humans is ongoing. In November 2007, the Centers for Disease Control and Prevention (CDC) published data on PFOA concentrations comparing 1999–2000 vs. 2003–2004 NHANES samples. In October 2021 the EPA proposed to designate PFOA and PFOS as hazardous substances in its PFAS Strategic Roadmap. In September 2022 the EPA proposed to designate as hazardous substances under the Superfund Comprehensive Environmental Response, Compensation, and Liability Act of 1980 (CERCLA). In 2024 EPA published drinking water regulations for PFOA and five other PFAS.
In August 2025, Moore's chief of staff, Fagan Harris, announced that he would resign his post at the end of the year to become the next president of the Abell Foundation; he was succeeded by Lester Davis, a CareFirst BlueCross BlueShield executive who worked as an unpaid outside advisor to Moore's 2022 gubernatorial campaign. In October 2025, Roland Butler resigned as secretary of state police and was succeeded by state senator Michael A. Jackson. In November 2025, Paul Monteiro resigned as secretary of Maryland Department of Service and Civic Innovation and was succeeded by Jonny Dorsey, one of Moore's deputy chiefs of staff. In October 2025, Moore appointed Walter Simmons to serve as the secretary of the newly created Department of Social and Economic Mobility. Two of Moore's cabinet secretaries resigned in 2026. Maryland Secretary of Human Services Rafael López, who resigned on February 23, citing health reasons, and was succeeded by deputy secretary Gloria Brown Burnett, who will serve as acting secretary until April 1, when Stacy Rodgers will then take over as acting secretary. In March 2026, Rai announced that he would step down on March 27, and would be succeeded by deputy secretary Elena Quiroz-Livanis, who will serve as acting secretary until a search for a new, permanent secretary is completed.
UPMC has its roots in the 1893 establishment of Presbyterian Hospital, which serves as the medical center's flagship facility, and the 1886 founding of the Western Pennsylvania Medical College. Soon after its founding, the medical college became affiliated with the Western University of Pennsylvania in 1892, and in 1908, was fully integrated into the university which that same year was renamed to the University of Pittsburgh. Already having informal agreements for teaching and staffing privileges with a number of local hospitals, Pitt and its School of Medicine desired to establish an academic medical center, and by the mid-1920s had formed a plan with city hospitals to have them relocate to the Oakland neighborhood where the university had moved in 1909. The university provided Presbyterian Hospital on the North Side, with a tract of land on its campus to construct a new hospital which broke ground in 1930 and opened in 1938. By the end of the 1930s, the University of Pittsburgh had helped to form the "University Medical Center" including Falk Clinic, Children's, Eye and Ear, Libby Steele Magee, Presbyterian General, and Women's Hospital, as well as the planned Municipal Hospital. In 1949, a new agreement between the university and Presbyterian Hospital established a three-tiered mission of patient care, research, and education, and by 1951, the hospital name was changed to Presbyterian University Hospital to reflect its close ties with the University of Pittsburgh.
Metabologenomics is a novel approach to integrate metabolomics and genomics data by correlating microbial-exported metabolites with predicted biosynthetic genes. This bioinformatics-based pairing method enables natural product discovery at a larger-scale by refining non-targeted metabolomic analyses to identify small molecules with related biosynthesis and to focus on those that may not have previously well known structures. Fluxomics is a further development of metabolomics. The disadvantage of metabolomics is that it only provides the user with abundances or concentrations of metabolites, while fluxomics determines the reaction rates of metabolic reactions and can trace metabolites in a biological system over time. Nutrigenomics is a generalised term which links genomics, transcriptomics, proteomics and metabolomics to human nutrition. In general, in a given body fluid, a metabolome is influenced by endogenous factors such as age, sex, body composition and genetics as well as underlying pathologies. The large bowel microflora are also a very significant potential confounder of metabolic profiles and could be classified as either an endogenous or exogenous factor. The main exogenous factors are diet and drugs. Diet can then be broken down to nutrients and non-nutrients. Metabolomics is one means to determine a biological endpoint, or metabolic fingerprint, which reflects the balance of all these forces on an individual's metabolism. Thanks to recent cost reductions, metabolomics has now become accessible for companion animals, such as pregnant dogs.
Henning Genz (2001). Nothingness: The Science Of Empty Space. Da Capo Press. ISBN 978-0-7382-0610-3. Luciano Boi (2011). The Quantum Vacuum: A Scientific and Philosophical Concept, from Electrodynamics to String Theory and the Geometry of the Microscopic World. Johns Hopkins University Press. ISBN 978-1-4214-0247-5.
Sources: en.wikipedia.org
Barbiturate drugs are obtained via condensation reactions between a derivative of diethyl malonate and urea in the presence of a strong base. The synthesis of phenobarbital uses this common approach as well but differs in the way in which this malonate derivative is obtained. The reason for this difference is because aryl halides do not typically undergo nucleophilic substitution in Malonic ester synthesis in the same way as aliphatic organosulfates or halocarbons do. To overcome this lack of chemical reactivity two dominant synthetic approaches using benzyl cyanide as a starting material have been developed: The first of these methods consists of a Pinner reaction of benzyl cyanide, giving phenylacetic acid ethyl ester. Subsequently, this ester undergoes cross Claisen condensation using diethyl oxalate, giving diethyl ester of phenyloxobutandioic acid. Upon heating this intermediate easily loses carbon monoxide, yielding diethyl phenylmalonate. Malonic ester synthesis using ethyl bromide leads to the formation of α-phenyl-α-ethylmalonic ester. Finally, a condensation reaction with urea gives phenobarbital.
Moderate alcohol consumption, one standard drink per day, by breastfeeding mothers is not known to significantly affect infants; however, the American Academy of Pediatrics strongly discourages more than two standard drinks per day. Even one or two drinks, including beer, may reduce milk intake by 20 to 23%, leading to increased agitation and poor sleep patterns. Regular heavy drinking (more than two drinks daily) can shorten breastfeeding duration and cause issues in infants, such as excessive sedation, fluid retention, and hormonal imbalances. Additionally, higher alcohol consumption may negatively impact children's academic achievement. When breastfeeding, alcohol may be consumed in moderation and does not require "Pumping-and-Dumping" (pumping and discarding breastmilk). Alcohol crosses from the blood to the breastmilk by diffusion. Thus, the concentration of alcohol in the breastmilk is approximately equal to the concentration in the maternal bloodstream at any given time. As the mother's liver processes the alcohol, more and more alcohol is pulled out of the breastmilk and back into the bloodstream. Thus, it is suggested to wait 2 hours after drinking before nursing or pumping. In the case of infrequent binge drinking, it has been shown that infants consume through breastmilk only a fraction of the alcohol their mothers have ingested. While a minute, clinically insignificant amount of alcohol may be absorbed into the infant's bloodstream, it is unlikely that this amount would cause any noticeable cognitive or neuromotor effects.
The topiramate molecule is a sulfamate modified sugar—more specifically, fructose diacetonide, an unusual chemical structure for a pharmaceutical. Topiramate is quickly absorbed after oral use. It has a half-life of 21 hours, and steady-state drug levels are reached in 4 days in patients with normal renal function. Most of the drug (70%) is excreted in the urine unchanged. The remainder is extensively metabolized by hydroxylation, hydrolysis, and glucuronidation. Six metabolites have been identified in humans, none of which constitutes more than 5% of an administered dose. Several cellular targets have been proposed as relevant to topiramate's therapeutic activity. These include voltage-gated sodium channels, high-voltage-activated calcium channels, GABAA receptors, AMPA/kainate receptors, and carbonic anhydrase isoenzymes. There is evidence that topiramate may alter the activity of its targets by altering their phosphorylation state rather than by direct action. The effect on sodium channels could be of particular relevance for seizure protection. Although topiramate does inhibit high-voltage-activated calcium channels, its relevance to clinical activity is uncertain. Effects on specific GABAA receptor isoforms could also contribute to the anticonvulsant activity of the drug. Topiramate selectively inhibits cytosolic (type II) and membrane-associated (type IV) forms of carbonic anhydrase. Its action on carbonic anhydrase isoenzymes may contribute to the drug's side effects, including its propensity to cause metabolic acidosis and calcium phosphate kidney stones.
Moore began announcing nominations for his 26-member cabinet on November 14, 2022. He finished announcing his cabinet nominees on April 12, 2023, with the nomination of Sanjay Rai as Secretary for the Maryland Higher Education Commission. According to The Baltimore Banner, Moore assembled his cabinet at a slower pace than previous Maryland governors. Three of Moore's Cabinet nominees, Secretary of Emergency Management Russell Strickland, Maryland State Police superintendent Roland Butler, and Secretary of Public Safety and Correctional Services Carolyn Scruggs, are holdovers from the Hogan administration. As his chief of staff, Moore chose Fagan Harris, who co-founded the Baltimore Corps organization with Moore a decade ago. Moore also named three members of the Maryland General Assembly to his administration: state senator Paul G. Pinsky as director of the Maryland Energy Administration; state senator Susan C. Lee as Secretary of State; and House of Delegates Majority Leader Eric Luedtke as chief legislative officer. Other notable Cabinet nominations included Salisbury mayor Jacob R. Day as Secretary of Housing and Community Development, former New York City Department of Correction commissioner Vincent Schiraldi as Secretary of Juvenile Services, Anthony Woods as Secretary of Veterans Affairs, and former WMATA general manager Paul Wiedefeld as Secretary of Transportation.
The UPMC Mercy South Side Outpatient Center, formerly UPMC South Side hospital, is a 209,000-square-foot (19,400 m2) urgent care and outpatient facility serving the South Side neighborhood of Pittsburgh. It is one of several UPMC outpatient medical facilities serving various communities throughout the region.
Sources: en.wikipedia.org
Non-radiogenic Pb is negligible compared to radiogenic Pb. No modification of U/Th/Pb has occurred except radioactivity. The first assumption tends to be true since monazite is very unlikely to incorporate Pb during its growth. The non-radiogenic Pb content in many laboratory tests was found to be very low, nearly always less than 1 ppm. The most common error arising from this assumption is contamination with lead during sample preparation. The second assumption is usually justified by the concordant behavior of the mineral observed in tests. That means the system is either reset totally or unaffected totally by geological processes, there is no partial resetting of the system. Minor errors may arise due to negligible disturbance during mass transfer. The theory is that monazite has high contents of Th (generally 3–15% and up to 25% of its weight) and U (generally hundreds of ppm and up to 5% in concentration). Thus, Pb accumulates at a high rate by radioactive processes. In less than hundreds of years, it reaches a level high enough to be measured accurately by an electron microprobe.
=== Breeding === Like many other gouramis, the male croaking gourami is a bubblenest builder, creating a small nest from air bubbles and mucus under a leaf. The water level should be reduced to 20 cm (7.9 in) during spawning, circulation kept minimal, and the temperature should be approximately 28 °C (82 °F). Spawning occurs under the nest, with the female responding to the male's dance by rolling over, followed by the typical gourami embrace. About 5 to 10 eggs are released in a quick burst. The male will grab the eggs and spit them into the nest, often adding a few more bubbles for good measure. This act may be repeated a dozen times or more until about 100 eggs are laid (some large females may lay more than 200). After spawning, the female should be moved to a different tank (to prevent her from eating the eggs). The male will keep the bubblenest maintained and tend to the eggs and fry, but when the fry are 2 to 3 days old, the male should also be removed (for the same reason). When first hatched, the fry should be fed infusoria, and later, baby brine shrimp and fine ground flakes. Freeze-dried tablets may also be fed to older fry.
==== Effects ==== In accordance with their psychedelic effects in humans, the 2C drugs produce the head-twitch response and wet dog shakes, behavioral proxies of psychedelic effects, in rodents. At least some 2C drugs, such as 2C-D and 2C-E, produce hyperlocomotion at lower doses in rodents. All 2C drugs produce hypolocomotion at higher doses in rodents. 2C drugs, including 2C-C, 2C-D, 2C-E, and 2C-I, substitute partially to fully for psychedelics like DOM, DMT, and LSD and/or for the entactogen MDMA in rodent drug discrimination tests. However, none of the assessed 2C drugs substituted for dextromethamphetamine, suggesting that they lack amphetamine-type or stimulant-like effects. In contrast to most psychedelics, at least two assessed 2C drugs, 2C-C and 2C-P, have shown reinforcing effects in rodents, including conditioned place preference (CPP) and self-administration. The mechanism by which these effects are mediated is unknown. However, it may be related to reduced expression of the dopamine transporter (DAT) and increased DAT phosphorylation, in turn resulting in increased extracellular dopamine levels in certain brain areas. These 2C drugs might have misuse potential in humans. Similar reinforcing effects in animals have been observed for NBOMe analogues of 2C drugs, including 25B-NBOMe, 25D-NBOMe, 25E-NBOMe, 25H-NBOMe, and 25N-NBOMe. Similarly to DOI, tolerance has been found to gradually develop to the head-twitch response induced by 2C-T-7 with chronic administration in rodents.
Adult cod are active hunters, feeding on sand eels, whiting, haddock, small cod, squid, crabs, lobsters, mussels, worms, mackerel, and molluscs. In the Baltic Sea the most important prey species are herring and sprat. Many studies that analyze the stomach contents of these fish indicate that cod is the top predator, preying on the herring and sprat. Sprat form particularly high concentrations in the Bornholm Basin in the southern Baltic Sea. Although cod feed primarily on adult sprat, sprat tend to prey on the cod eggs and larvae. Cod and related species are plagued by parasites. For example, the cod worm, Lernaeocera branchialis, starts life as a copepod-like larva, a small free-swimming crustacean. The first host used by the larva is a flatfish or lumpsucker, which it captures with grasping hooks at the front of its body. It penetrates the fish with a thin filament, which it uses to suck the fish's blood. The nourished larvae then mate on the fish. The female larva, with her now fertilized eggs, then finds a cod, or a cod-like fish such as a haddock or whiting. There the larva clings to the gills while it metamorphoses into a plump sinusoidal wormlike body with a coiled mass of egg strings at the rear. The front part of the worm's body penetrates the body of the cod until it enters the rear bulb of the host's heart. There, firmly rooted in the cod's circulatory system, the front part of the parasite develops like the branches of a tree, reaching into the main artery.
Sources: en.wikipedia.org
Method validation is the documented process of showing that an HPLC procedure produces reliable results for a defined purpose. It examines parameters such as accuracy, precision, specificity, linearity, and robustness. Regulators and quality systems often require validation before routine use.
System suitability is a set of checks run on the chromatographic system before sample analysis. It confirms that resolution, peak shape, retention time, and response meet predefined limits. Failure can invalidate the run and trigger corrective action.
Blank injections reveal peaks or baseline disturbances that come from solvents, reagents, or the instrument rather than the sample. They help distinguish contamination from actual analyte signals. Comparing blanks with sample runs supports accurate interpretation.
It is a set of checks performed before or during an HPLC run to confirm the system works as expected. Parameters may include resolution, tailing factor, theoretical plates, and retention time precision. Failure can trigger maintenance, method adjustment, or repeat analysis.